- PCB50E WILLEM EPROM PROGRAMMER SOFTWARE DOWNLOAD SOFTWARE
- PCB50E WILLEM EPROM PROGRAMMER SOFTWARE DOWNLOAD PC
- PCB50E WILLEM EPROM PROGRAMMER SOFTWARE DOWNLOAD WINDOWS
Or directly input the address data, the range is: 0-7FFFFH A0-PIN 12, A1-PIN 11, A2-PIN 12, A3-PIN 9, A4-PIN 8, A5-PIN 7, A6-PIN 6, A7-PIN 5, A8-PIN 27, A9-PIN 26,A10-PIN 23, A11-PIN 25, A12-PIN 4, A13-PIN 28, A14-PIN 29, A15-PIN 3, A16-PIN 2, A17-PIN 30 Data Pin Test: click one of the push button in Data Out group, use multimeter confirm the data from ZIF socket. Operation Steps: Before test, set the DIP switch, jumper setup is default Address Pin Test: click the one of the push button in the Address Out group, use multimeter detect output signal in the ZIF32 socket. When programming a chip, please ensure the dial switch setting is the same as DIP switch displayed in the program, otherwise, and make sure the safety protection jumper is enabled (closed). Safe protection normally at safe position, after programming of the special chip, please set back the jumper. Since this programmer has build-in FWH/LPC, PLCC32, P28F002BC adaptors, it directly supports Intel810, 815, 845 main board N82802AB, SST49LF002, SST49LF004 and etc 3.3Vchips 2. When programming one chip, follow the program prompt to set DIP switch. The J4, J3 jumper drawing: to 4M and 8M chips, when use it, the program prompts accordingly. When programming PIC MCU, the program prompts the connection method. ICSP Socket: to connect the PIC MCU adaptor. A fter the chip programming, ensure to reset safety protection jumper to default position. After takeoff the jumper, the rest button return to normal situation. Safety Jumper: to ensure the programmer at safe status: when this jumper is enabled(closed), the special model conversion and voltage cycle conversion are disable, the programmer is forced to work at the normal safe status to normal chip. Hi-voltage may damage the chip if selected a wrong voltage. Note, normally, the voltage is 12V, only certain the chip needs higher voltage, then it sets up to voltage above 12V. when press this switch, the voltage cycles among 12V, 15V, 21V, 25V, and the voltage can be read from LED. VPP Setting Switch: to configure 27series chip programming voltage. Special Chip Switch: to configure the 2732, 2716, 2816, I28F001, AT29C256 special chips, when press this switch, the internal circuits automatically switch between those chips, the status is directly indicated by the LED. There is a Safety Jumper located on the top of the board. In the above picture shows three black color buttons. They are: Reset Swithc, VPP Setting Switch and Special Chip Switch. On the middle top of the board, three push button switches. Please note only one chip programming is allowed at the same time, otherwise the error will occur when programming or chip may be damaged. They are DIP32, PLCC32, FWH/LPC, 25CXX, 24CXX, 93CXX, PIC16F84 and etc. The blue portion is the socket of the target chips. If the connection and power supply is normal, then appears: "Hardware present"
PCB50E WILLEM EPROM PROGRAMMER SOFTWARE DOWNLOAD SOFTWARE
Software Operation The software interface:Īfter start the program, click test hardware under Help menu, if the power supply or connection is wrong, appears the prompt, please check if the programmer connects well with
PCB50E WILLEM EPROM PROGRAMMER SOFTWARE DOWNLOAD PC
Note: the LPT port of PC needs setting to ECP or ECP+EPP during BIOS setup.ģ. Then, the two programmer normal indicators light up, then the programmer power supply is normal, the hardware connection is ok. Turn off PC power supply Connect one end of the cable to PC printer port Connect the other end to 25 Pins port of the programmer Connect A-A type (Male-Male) USB cable to the programmer and PC.
PCB50E WILLEM EPROM PROGRAMMER SOFTWARE DOWNLOAD WINDOWS
The hardware is fully compatible with original Willem EPROM Programmer (PCB3B) and Windows software. Added PLCC32, FWH/LPC and P28F002BC adapters on board. The USB cable is A-A type Male-to-Male connector. Added a USB port to make use of USB power. And Reset key provides a quicker way to reset VPP and Special Chip configuration to normal state. Safety Jumper will disable all VPP and Special Chip changing to avoid misconfiguring accidentally. Added a Safety Jumper and a Reset key to gave more protection when programming. There are 7 LEDs to indicate the chip type been selected currently.(Normal, 2732, 2716, i28F, AT29, W27C) 4. The special chip selection key provides a simple way to select a chip type by pressing the Special Chip key. There are 4 LEDs to indicate the VPP currently been selected. For this Enhanced Willem EPROM Programmer, VPP can be configured by just press the VPP setting key. So that to protect this programmer not be damaged by mis-configured VPP jumper. Added isolation circuit (between VPP and pin). What's new about this Enhanced Willem EPROM Programmer from PCB3B?ġ. 18 Willem Programmer Supported Device List. Enhanced Willem EPROM Programmer – ManualĬontent What's new about this Enhanced Willem EPROM Programmer from PCB3B?.